Give a gift card. Let them choose their next make. Shop gift cards Skip to content

Thread the sewing machine

Set up the upper thread and quick-set bobbin on a Brother LX3817.

  1. 1Meet the machine

    Meet the machine

    Meet the machine. Find the parts used to thread and sew.

    Find the parts used to thread and sew.

  2. 2Connect power and pedal

    Connect power and pedal

    Connect power and pedal. Connect the foot-controller plug to the machine, then the power plug to a wall outlet. Put the pedal on the floor.

    Connect the foot-controller plug to the machine, then the power plug to a wall outlet. Put the pedal on the floor.

  3. 3Raise foot and needle

    Raise foot and needle

    Raise foot and needle. Lift the presser foot. Turn the handwheel toward you until its mark points up.

    Lift the presser foot. Turn the handwheel toward you until its mark points up.

  4. 4Fit the upper bobbin

    Fit the upper bobbin

    Fit the upper bobbin. Raise the spool pin and place a wound plastic bobbin on it for the upper thread.

    Raise the spool pin and place a wound plastic bobbin on it for the upper thread.

  5. 5Use the top guide

    Use the top guide

    Use the top guide. Draw thread from the upper bobbin through the rear guide, then toward the front groove.

    Draw thread from the upper bobbin through the rear guide, then toward the front groove.

  6. 6Down and around

    Down and around

    Down and around. Follow the right channel down, around the bottom, and up the left channel.

    Follow the right channel down, around the bottom, and up the left channel.

  7. 7Catch the take-up lever

    Catch the take-up lever

    Catch the take-up lever. Pass through the raised lever from right to left.

    Pass through the raised lever from right to left.

  8. 8Behind the needle guide

    Behind the needle guide

    Behind the needle guide. Bring the thread down behind the small guide above the needle.

    Bring the thread down behind the small guide above the needle.

  9. 9Thread front to back

    Thread front to back

    Thread front to back. Pass through the needle eye from front to back. Leave about 2 inches behind the foot.

    Pass through the needle eye from front to back. Leave about 2 inches behind the foot.

  10. 10Open the bobbin cover

    Open the bobbin cover

    Open the bobbin cover. Keep the needle and foot raised. Slide the cover toward you and lift it off.

    Keep the needle and foot raised. Slide the cover toward you and lift it off.

  11. 11Drop in the bobbin

    Drop in the bobbin

    Drop in the bobbin. Use a wound SA156 bobbin. Its thread must unwind counterclockwise.

    Use a wound SA156 bobbin. Its thread must unwind counterclockwise.

  12. 12Follow the slit and cut

    Follow the slit and cut

    Follow the slit and cut. Hold the bobbin gently. Follow the slit under the spring, then pull toward the cutter.

    Hold the bobbin gently. Follow the slit under the spring, then pull toward the cutter.

  13. 13Close the cover

    Close the cover

    Close the cover. Seat the cover tab and close it. The quick-set bobbin is ready; no pull-up is required.

    Seat the cover tab and close it. The quick-set bobbin is ready; no pull-up is required.

  14. 14Switch on

    Switch on

    Switch on. When threading is complete, press I on the power switch. The pedal controls sewing speed.

    When threading is complete, press I on the power switch. The pedal controls sewing speed.

Tips
  1. 1Optional: leave a bobbin tail

    Optional: leave a bobbin tail

    Optional: leave a bobbin tail. To draw up the lower thread, reinstall the bobbin without cutting its tail. Leave the cover off.

    To draw up the lower thread, reinstall the bobbin without cutting its tail. Leave the cover off.

  2. 2Catch the lower thread

    Catch the lower thread

    Catch the lower thread. Hold the upper thread. Turn the wheel toward you one full turn; pull up the bobbin loop.

    Hold the upper thread. Turn the wheel toward you one full turn; pull up the bobbin loop.

  3. 3Tails toward the back

    Tails toward the back

    Tails toward the back. Put about 4 inches of both threads behind the raised foot. Replace the cover.

    Put about 4 inches of both threads behind the raised foot. Replace the cover.